Skip to main content

Difference Between Sulfate And Sulfonate In Shampoo

Methyl iodide has been highlighted as a potential genotoxic impurity (PGI). A sensitive HS-GC method with ECD was developed and validated for the determination of methyl iodide impurity in Tedizolid phosphate, an active pharmaceutical ingredient. HS-GC method on DB-624,column 60m × 0.53mm, film thickness 3μm, with electron capture detector (ECD) was used. The proposed method was specific, linear, accurate, rugged and precise. The calibration curves showed good linearity over the concentration range of 0.78 μg/g to 11.7 μg/g and the correlation coefficient was 0.997. Method had very low limit of detection (LOD) and limits of quantification (LOQ) are 0.23 μg/g and 0.78 μg/g, respectively, with respect to test concentration. Accuracy was observed within the range 96.0% to 103.2%. This method is a further extended good quality control tool for low level quantitation of methyl iodide impurity in another API, alogliptin benzoate.

Methyl iodide is such a special electrophile, however, that successful alkylations with it cannot usually be used as an indication that alkylations with higher homologs or with more reactive alkylating agents such as allylic or benzylic halides, will necessarily be so rewarding.

Labels:

Comments

Post a Comment

Popular posts from this blog

Difference Between Sulfate And Sulfonate In Shampoo

  Sulfates and sulfonates have two things in common. First, they're all anionic surfactants. Second, they are often used for personal care applications. But there are many differences. They have different molecular mechanisms. They have different functions and they have different raw materials.   Sulfates Sulfate is a compound. It has carbon bonds and oxygen and sulfur bonds. They include substances such as sodium lauryl sulfate and sodium lauryl ether sulfate.   At low pH, these substances plus the c-o-s bond hydrolyze to produce alcohol and inorganic sulfate. At a high pH, sulfate is stable in the base and, if ethoxylated to a relatively high level, produces a low-foaming alkali-soluble surfactant. Sulphates can be prepared by reaction of fatty alcohol or fatty alcohol ethoxylates with reagents such as SO3 or chlorosulfonic acid (CSA).   The reason shampoo becomes thick foam in the shower is that it contains sulfate. Most shampoos and household cleansers contain su...
Post a Comment
Read more

What is Polyether Polyol

  Polyether polyol is prepared by ring-opening polymerization of epoxide monomers (such as ethylene oxide, propylene oxide and 1,2-epoxybutane) and a compound containing two or more active hydrogen atoms (called an initiator). In the presence of alkali catalyst, active hydrogen compounds initiate ring opening and oxide addition will continue until the required molecular weight is obtained. The number of hydroxyl groups in polyether polyol is determined by the number of unstable hydrogen atoms in the initiator. If the initiator has two active hydrogen, glycol will be formed. The reactivity of polyether polyol  to isocyanates depends on the initiator and the type of epoxy monomer that ends the ring-opening polymerization. The primary hydroxyl produced by polyol capped with ethylene oxide is more reactive than the secondary hydroxyl produced by propylene oxide, which is ideal for applications requiring rapid curing time. However, the use of initiator based on ethylene oxide and a...
Post a Comment
Read more

Polyether Polyol Manufacturing Process

  Synthesis of DMC-based polyether polyol by a continuous method   A certain amount of DMC catalyst is taken and uniformly dispersed in a certain amount of small molecule initiator. Add 0.5 kg of the mixture of the initiator in the small test reactor. The vacuum was replaced 1-2 times with N2, and the N2 pressure was maintained at 0.1 MPa. After heating, stirring and raising the temperature to a certain temperature, the quantitative PO was introduced into the continuous autoclave with nitrogen gas for induction. When the induction is successful (the temperature in the kettle rises and the pressure drops), the PO is continuously passed to carry out the reaction. Open the outer loop and continue to pass the PO into the continuous kettle.   When the liquid in the reaction vessel is full, the PO, DMC catalyst and the initiator are continuously added to the kettle at a certain ratio and a certain speed through the power system. Continuous discharge is started when a certain pr...
Post a Comment
Read more